Search
Search
View additional product information for DynaMag™-2 Magnet - FAQs (12321D)
20 product FAQs found
DynaMag-2磁力架的最低高斯值为3,500–3,700，DynaMag-Spin磁力架最低高斯值为3,000–3,500。
1特斯拉等于10,000高斯。
使用以下任意一种清洁剂喷洗和/或擦拭DynaMag磁力架：
•70%异丙醇
•1%次氯酸钠溶液（漂白剂）
•0.1 N HCl溶液
不要将装置浸泡在水溶液中，避免长时间接触于水或其他水溶液。不可将磁力架进行高压灭菌或加热至70°C以上。
DynaMag-2磁力架可容纳16个标准的1.5 mL或2 mL微量离心管，而DynaMag-Spin磁力架最多能容纳6个标准的1.5 mL微量离心管。
用下列试剂之一喷洗和/或擦拭DynaMag磁力架，这些试剂经测试可用于清洁磁力架：
•70%异丙醇
•1%次氯酸钠溶液（漂白剂）
•0.1 N HCl溶液
其它未经测试的消毒剂可能不适用。不要将磁力架浸没在水溶液中，也应避免长时间暴露于水或水溶液中。接触到强溶剂时使用湿布和柔和的清洁剂来进行清洁。不要对DynaMag磁力架进行高压灭菌，当加热至70°C以上时，磁力架的材质会丧失稳定性，进而导致磁力减弱。
我们推荐您按照样本体积来挑选磁力架：
•Invitrogen DynaMag-2 Magnet（货号12321D）磁力架的工作体积：1 µl–1.5 mL的样本体积
•Invitrogen DynaMag-5 Magnet（货号12303D）磁力架的工作体积：1–5 mL的样本体积
•Invitrogen DynaMag-15 Magnet（货号12301D）磁力架的工作体积：4-15 mL的样本体积
•Invitrogen DynaMag-50 Magnet（货号12302D）磁力架的工作体积：10-50 mL的样本体积
•Invitrogen DynaMag-96 Side Magnet（货号123-31D）将磁珠吸附至每一孔的一侧。兼容PCR联管和96孔平板（200 μL），无裙边和半裙边的产品
•Invitrogen DynaMag-96 Bottom Magnet（货号123-32D）：将磁珠吸附至每一孔的底部。兼容PCR联管和96孔平板（200 μL），无裙边和半裙边的产品
The DynaMag-2 Magnet is 3,500-3,700 minimum Gauss level and the DynaMag-Spin is 3,000-3,500 minimum Gauss level.
Find additional tips, troubleshooting help, and resources within our Protein Assays and Analysis Support Center.
1 Tesla is equivalent to 10,000 Gauss. .
Spray and/or wipe the DynaMag magnet unit with one of the following cleaning agents:
- 70% (v/v) isopropyl alcohol
- 1% (v/v) sodium hypochlorite solution (bleach)
- 0.1 N HCl solution
Do not submerge the magnet unit in aqueous solutions and avoid prolonged exposure to water or aqueous solutions. Clean with a damp cloth and mild detergent when exposed to harsh solvents. Do not autoclave the magnet unit as heating the magnet to above 70 degrees C can destabilize the magnetic material, resulting in loss of magnetic strength.
The DynaMag-2 Magnet can hold 16 standard 1.5 mL or 2 mL microcentrifuge tubes, while the DynaMag-Spin Magnet holds up to 6 standard 1.5 mL microcentrifuge tubes.
Superparamagnetic means that the Dynabeads magnetic beads exhibit magnetic properties when placed within a magnetic field, but have no residual magnetism when removed from the magnetic field.
This means that your targeted cells, proteins, or nucleic acids are only subjected to magnetic forces during the time the beads are on the magnet. The beads do not aggregate, but remain evenly dispersed in suspension.
Find additional tips, troubleshooting help, and resources within our Dynabeads Cell Isolation and Expansion Support Center.
Yes. The antibodies are covalently bound and should be very stable in your applications.
Find additional tips, troubleshooting help, and resources within our Protein Assays and Analysis Support Center.
Depending on the antibody coated on the Dynabeads magnetic beads, the shelf life can vary from 24-36 months.
Some kits may have 18 months shelf life depending on other components supplied in the kit. The kits are guaranteed for 6 months from when you receive them.
Find additional tips, troubleshooting help, and resources within our Dynabeads Nucleic Acid Purification Support Center as well as our Protein Immunoprecipitation (IP), Co-Immunoprecipitation (Co-IP), and Pulldown Support Center.
The strength of the DynaMag-2 Magnet is a minimum of 3,500-3,700 Gauss.
Find additional tips, troubleshooting help, and resources within our Protein Purification and Isolation Support Center.
Yes, the plastic part of the DynaMag-2 Magnet stand can be purchased as a stand-alone product (SampleRack (for DynaMag-2 magnet), Cat. No. 12322D).
Find additional tips, troubleshooting help, and resources within our Protein Assays and Analysis Support Center.
1 Tesla is equivalent to 10,000 Gauss
Find additional tips, troubleshooting help, and resources within our Protein Assays and Analysis Support Center.
Spray and/or wipe the DynaMag magnet unit with one of the following cleaning agents:
- 70% (v/v) isopropyl alcohol
- 1% (v/v) sodium hypochlorite solution (bleach)
- 0.1 N HCl solution
Do not submerge the magnet unit in aqueous solutions and avoid prolonged exposure to water or aqueous solutions. Clean with a damp cloth and mild detergent when exposed to harsh solvents. Do not autoclave the magnet unit as heating the magnet to above 70 degrees C can destabilize the magnetic material, resulting in loss of magnetic strength.
Find additional tips, troubleshooting help, and resources within our Protein Assays and Analysis Support Center.
The DynaMag-2 Magnet (Cat. No. 12321D) can hold 16 standard 1.5 mL or 2 mL microcentrifuge tubes, while the DynaMag-Spin Magnet (Cat. No. 12320D) holds up to 6 standard 1.5 mL microcentrifuge tubes.
Find additional tips, troubleshooting help, and resources within our Protein Assays and Analysis Support Center.
Spray and/or wipe the DynaMag magnet unit with one of the following cleaning agents:
- 70% (v/v) isopropyl alcohol
- 1% (v/v) sodium hypochlorite solution (bleach)
- 0.1 N HCl solution
Do not submerge the magnet unit in aqueous solutions and avoid prolonged exposure to water or aqueous solutions. Clean with a damp cloth and mild detergent when exposed to harsh solvents. Do not autoclave the magnet unit as heating the magnet to above 70 degrees C can destabilize the magnetic material, resulting in loss of magnetic strength.
Find additional tips, troubleshooting help, and resources within our Cell Analysis Support Center.
We recommend that you select a magnet based on your sample volume:
- Invitrogen DynaMag-2 Magnet (Cat. No. 12321D) magnet working volume: 1 µl-1.5 mL sample volume
- Invitrogen DynaMag-5 Magnet (Cat. No. 12303D) magnet working volume: 1-5 mL sample volume
- Invitrogen DynaMag-15 Magnet (Cat. No. 12301D) magnet working volume: 4-15 mL sample volume
- Invitrogen DynaMag-50 Magnet (Cat. No. 12302D) magnet working volume: 10-50 mL sample volume
- Invitrogen DynaMag-96 Side Magnet (Cat. No. 123-31D): pulls beads to the side of each well. Compatible with PCR-strips and 96-well plates (200µL), non-skirted and half-skirted
- Invitrogen DynaMag-96 Bottom Magnet (Cat. No. 123-32D): pulls beads to the bottom of each well. Compatible with PCR-strips and 96-well plates (200µL) non-skirted and half-skirted
Find additional tips, troubleshooting help, and resources within our Cell Analysis Support Center.