MicroAmp™ 光学黏性封板膜套件

货号	数量
4313663	1 kit

货号 4313663

价格（CNY)

457.00

Ends: 31-Dec-2025

1,127.00

共减 670.00 (59%)

添加至购物车

1 kit

价格（CNY)

457.00

Ends: 31-Dec-2025

1,127.00

共减 670.00 (59%)

添加至购物车

Applied Biosystems™ MicroAmp™ 光学黏性封板膜套件包括以下产品：

•当应用于微孔板时，MicroAmp™ 光学黏性封板膜减少了孔间污染和样品蒸发的可能性。

•MicroAmp™ 光学膜压缩垫设计用于在使用黏性封板膜时，在热循环仪与反应板之间提供适当热封效果

• MicroAmp™ 黏性封板膜封膜机用于在微孔板和黏性封板膜之间形成紧密密封。

MicroAmp™ 光学黏性封板膜应用于微孔板时减少了发生孔间污染和样品蒸发的可能性。

•压敏粘合剂紧密密封每个孔

•不会干扰样品读数

•加压密封：对齐微孔板，然后按压以密封

•易于使用，不粘手套

防止珍贵样品丢失
使用此光学透明的黏性封板膜将样品密封到微孔板的孔中。这将降低样品孔间交叉污染的可能性，并有助于确保实时荧光定量 PCR 数据的一致性。

易于使用
只需剥去黏性封板膜的背衬，然后紧紧包住微孔板顶面。像平时一样堆叠微孔板和读取样品，但发生样品污染的可能性更小。适用于 MicroAmp™ 光学 96 孔反应板。

MicroAmp™ 光学膜压缩垫设计用于在使用粘合封板膜时在热循环仪和反应板之间提供适当热封效果。

使用 MicroAmp™ 黏性封板膜封膜机在微孔板和黏性封板膜之间形成紧密密封。

形成紧密密封
MicroAmp™ 黏性封板膜封膜机使您能够以符合人机工效学的方式将黏性封板膜向下推至微孔板上，形成紧密的密封并尽量减少气泡。这种密封方式可防止孔间污染和样品损失。

快速简便
使用 MicroAmp™ 封膜机可快速密封多个微孔板。该工具根据微孔板尺寸设计，因此您可以快速密封微孔板。耐用的专有塑料可持续使用，使您可以完成大型筛选应用。

注：有关有限的标签许可和商标信息，请参见用户手册或包装说明书。

适用于（设备）2720 热循环仪、6100 热循环仪、7000 系统、7900HT 系统、GeneAmp 9700、QuantStudio™、ViiA™ 7 Dx 系统、ViiA™ 7 系统、QuantStudio™ Dx

产品类型膜，密封或封膜机

数量1 kit

运输条件室温

黏合剂压力敏感

孔数量96

板兼容性96 孔板

产品线MicroAmp

Unit SizeEach

内容与储存

包含：MicroAmp™ 光学黏性覆膜（数量 20）、封膜机（数量 1）、MicroAmp™ 光学覆膜压缩垫（数量 1）

常见问题解答 (FAQ)

How do I correctly apply MicroAmp Optical Adhesive Covers to an optical 96- or 384-well plate?

Please follow the instructions below for the proper application of MicroAmp Optical Adhesive Covers (Cat. Nos. 4311971, 4313663 and 4360954).

The MicroAmp Optical Adhesive Cover uses a pressure-sensitive adhesive backing to adhere the cover to the optical 96- or 384-well plate. It is imperative that you use enough force to activate the pressure-sensitive adhesive to prevent evaporation from the wells.
Please note: Users should not expect the Optical Adhesive Cover to be very sticky to the touch on the side that adheres to the optical plate.

The correct way to apply the cover is as follows:

1. Apply firm pressure when using the Adhesive Seal Applicator (Cat. No. 4333183) to press the cover onto the plate.

2. Run the applicator firmly from left to right several times. Run the applicator up and down several times.

3. Run the edge of the applicator around the border (following the red line outside the wells) of the cover.

4. Repeat the left to right and up and down motions to assure a good final seal.

5. Inspect each well to make sure that each well edges are imprinted on the optical adhesive cover.
Please Note: Using the Applicator's edge to seal between the wells is NOT recommended. It may actually pull the seal off the wells.

Find additional tips, troubleshooting help, and resources within our Real-Time PCR and Digital PCR Instruments Support Center.

Can the MicroAmp Optical Adhesive Film be used with MicroAmp Optical Tubes?

No. The Optical Adhesive Film is recommended for use only with the MicroAmp Optical 96-well Reaction Plate (with or without barcode) and MicroAmp 384-well Optical Reaction Plate.

Find additional tips, troubleshooting help, and resources within our Real-Time PCR and Digital PCR Instruments Support Center.