Search

  • 联系我们
  • 货号直购

NuPAGE™ Large Protein Blotting Kit - FAQs

查看更多产品信息 NuPAGE™ Large Protein Blotting Kit - FAQs (LP0001)

5 个常见问题解答

我将蛋白质置于Tris-甘氨酸凝胶上在非变性条件下进行电泳。蛋白质的pI高于Tris-甘氨酸转膜缓冲液的pH。你们建议如何对蛋白质进行转印？

•将Tris-甘氨酸转膜缓冲液的pH增加至9.2，可使pl低于9.2的所有蛋白质朝阳极方向迁移。
•使用Tris-甘氨酸转膜缓冲液，并在凝胶两侧各放一张膜。碱性高于转膜缓冲液pH的蛋白质，将被凝胶阴极侧的膜捕获。随后，可以用相同的方式处理两张膜。
•转印前，将凝胶置于含0.1% SDS的Tris-甘氨酸转膜缓冲液中孵育15分钟。少量的SDS会给予蛋白质足够的电荷，使蛋白质朝阳极端单向移动，并且在大部分情况下不会使蛋白质变性。然后，使用常规Tris-甘氨酸转膜缓冲液进行转印。

Can I prepare my protein sample with the reducing agent and store it for future use?

DTT is not stable, so it must be added and the reduction performed just prior to loading your samples.

Find additional tips, troubleshooting help, and resources within our Protein Gel 1D Electrophoresis Support Center.

My LDS or SDS sample buffer precipitates when stored at 4 degrees C. Can I warm it up? Can I store it at room temperature?

Precipitation of the LDS or SDS at 4 degrees C is normal. Bring the buffer to room temperature and mix until the LDS/SDS goes into solution. If you do not want to wait for it to dissolve, you can store the sample buffer at room temperature.

Find additional tips, troubleshooting help, and resources within our Protein Gel 1D Electrophoresis Support Center.

How are Bolt gels different than NuPAGE gels?

While they are both Bis-Tris based gels, the chemistries are very different since Bolt gels are optimized for western blotting. Another key difference is the wedge well design of the Bolt gels, which allows larger sample volumes to be loaded.

Find additional tips, troubleshooting help, and resources within our Protein Gel 1D Electrophoresis Support Center.

I ran my protein under native conditions on a Tris-Glycine gel. It has a pI that is higher than the pH of the Tris-Glycine transfer buffer. Can you offer some tips for transferring it?

- Increase the pH of Tris-Glycine transfer buffer to 9.2, allowing all the proteins below pI 9.2 to transfer towards the anode electrode.
- Use the Tris-Glycine transfer buffer and place a membrane on both sides of the gel. If there are any proteins that are more basic than the pH of the transfer buffer, they will be captured on the extra membrane placed on the cathode side of the gel. Both membranes can then be developed in the same manner.
- Prior to blotting, incubate the gel for 15 minutes in Tris-Glycine transfer buffer containing 0.1% SDS. The small amount of SDS will give the proteins enough charge to move unidirectionally towards the anode and in most cases, should not denature the protein. Proceed with the transfer using regular Tris-Glycine transfer buffer.

Find additional tips, troubleshooting help, and resources within our Protein Electrophoresis and Western Blotting Support Center.